Design a soccer ball, spin it around, then cut the panels with every stitch hole already in place. Every seam matches its neighbour, hole for hole.
Drag to spin. Click a panel to paint it.
The 3D preview needs WebGL, which this browser has switched off. The patterns still work.
Pick a pattern
The big number is how many panels youâll sew. More panels means a rounder ball and a lot more stitching.
The middle is the even, regular version. Slide left for small accent panels, right for big ones.
Pick a ball size above, or drag for anything in between.
The skin stretches a little under pressure, so the pattern is cut slightly small to land on your target size.
Loose balls stall on your foot. Full ones pop off it.
First one came out the wrong size?
Measure around the middle, divide by 3.14, and type the diameter here. Every pattern after that gets corrected.
Colour it
Tap a swatch, then click panels on the ball to paint them one at a time. Or let a scheme do the lot.
Palettes
Add art
Type something or upload a logo, then click panels on the ball to stamp it. Art is cut from heat transfer vinyl, so everything becomes a one-colour shape.
Font
100% fills the safe area of whichever panel you click.
The vinyl file is already mirrored and sized, one file per vinyl colour. Each design sits in a square weeding box whose middle is the middle of the art. Panels with art get a pen cross on the fabric with a long arm pointing to the top of the design.
Cutting sheets
One SVG per colour, laid out to fit your mat. Sizes are in real millimetres.
5 mm is typical for a hand-stitched ball. The stitch holes sit on this line.
Both sides of every seam get the same number of marks, so they pair up as you sew.
CutDraw or scoreLabels
The file has three layers named cut, stitch-guide and labels. In Cricut Design Space, set the blue layer to Pen (or delete it) and the red layer to Basic Cut before you hit Make. Laminated ball material is thick, so a laser or hand cutting from printed templates is the dependable route. A Cricut can cut thin faux leather and paper templates.
Sew-along
Step through the build one panel at a time. The numbers match the ones on your cutting sheet.
The whole method
Add heat transfer vinyl
Press vinyl art onto the flat panels after cutting and before any sewing. Once the ball is sewn thereâs nothing flat left to press against.
Size the artKeep each design inside the size shown above. That leaves 3 mm clear of the stitch line, so the needle never has to punch through vinyl and the art doesnât wrap into a seam.
Pick stretch vinylA ball flexes on every kick. Stretch heat transfer vinyl bends with the fabric; standard vinyl cracks sooner. Skip thick glitter and flock on small panels.
Mirror and cutFlip the design in your cutting software, load the vinyl shiny carrier side down, and cut. Weed away everything that isnât the art.
Mark the panel centreTick âCentre marks for vinylâ in the Cut file tab. Your machineâs fabric pen then draws a small cross at the exact middle of every panel, on the good side.
Mark the art centreIf you placed art in the Art tab, its vinyl file cuts a square around each design, so trim on the square and rule corner to corner to find the middle. Otherwise, draw a box around the art in your software and note its middle. On the back of the clear carrier, rule a cross through that middle with a fine marker. For round or symmetrical art, a light fold of the carrier in half each way gives you the same cross.
Line up the crossesLay the panel good side up on a firm pressing mat. Set the carrier down so its cross sits on the panelâs cross. To keep the art straight, point its top at one corner or one flat edge, and use the same choice on every panel. The corner crosses on the pattern help you sight it.
PressCover with parchment or a pressing sheet. Use a mini heat press or the tip of an iron, firm pressure, in short presses of about 10 seconds. Follow the vinylâs own temperature, but synthetic leather scorches and wrinkles easily: choose a low-temperature vinyl, stay at or under about 265°F (130°C), and test a scrap first.
Peel and setPeel the carrier warm or cool, whichever the vinyl maker says. If an edge lifts, lay the parchment back and press again for 5 seconds. Let panels cool flat before you sew, and never iron the finished ball.
Supplies
What goes into a hand-stitched ball, from the skin to the pump.
As an Amazon Associate I earn from qualifying purchases. Cards marked âOur pickâ go straight to one product; the rest open an Amazon search for that item.